home *** CD-ROM | disk | FTP | other *** search
/ System Booster / System Booster.iso / Archives / HardwareProjects / RAM_2630.lha / Umbau.englisch < prev   
Encoding:
Text File  |  1994-03-19  |  4.1 KB  |  138 lines

  1. Instructions:
  2. -------------
  3.  
  4. In following steps, the reconstruction of A2630-Board is described in detail.
  5.  
  6. Parts list :
  7.  
  8.  8 MB:    16 x Ram (TC514400AZ-100 or faster)
  9.     16 x ZIP-sockets or single inline sockets (SIL-sockets)
  10.      1 x 74F257 (in case of damaging original)
  11.      1 x 16-pol. IC-socket
  12.      1 x 33 Ohm resistor
  13.      ca. 1 meter isolated wire, 0.25 mm diameter
  14.  
  15. 16 MB:    32 x Ram (TC514400AZ-100 or faster)
  16.     32 x ZIP-sockets or single inline sockets (SIL-sockets)
  17.      1 x 74F138
  18.      1 x 74F257 (in case of damaging original)
  19.      1 x 16-pol. IC-socket
  20.      1 x 33 Ohm resistor
  21.      ca. 1 meter isolated wire, 0.25 mm diameter
  22.  
  23. *******  2 new pals (Contact address see end of text)
  24.  
  25. ------------------------------------------------------------------------------
  26.  
  27. 1.    Desolder rams U400 - U431        see picture '2630.rams'.
  28.  
  29.  
  30. 2.    Free all soldering-pads of rams.
  31.     (work carefully)
  32.  
  33. 3.    Mount SIL-sockets (resp. special ZIP-sockets) to places
  34.     U400 - U431. (later location of rams)
  35.  
  36.  
  37. 4.    Connect all Pin 10 of ram-sockets    see picture '2630.mux'
  38.  
  39.  
  40. 5.    Desolder U104 and perform orders described in picture '2630.u104'
  41.  
  42.  
  43. 6.    Connect U104 pin 5 with U304 pin 11 with a wire and do the
  44.     same with U104 pin 6 and U304 pin 13.
  45.     see picture '2630.mux'
  46.  
  47.  
  48.  
  49. ********************* A T T E N T I O N **********************
  50. *                                                            *
  51. * Complete section '7. - 7.5'  only for 16 MB reconstruction *
  52. *      Continue with step '8.' for 8 MB reconstruction.      *
  53. *                                                            *
  54. **************************************************************
  55.  
  56. 7.    Mount additionally used IC (Typ 74F138) as follows :
  57.  
  58. 7.1    Prepare : All pins of 74F138 (except of pin 8 and 16)
  59.     must be shortened downto approx. 2-3 mm. ( 1/10 inch)
  60.  
  61. 7.2    Mount IC 74F138 with glue on A2630 upside down.
  62.     see picture '2630.138'
  63.  
  64. 7.3    Carefully bend pin 8 and 16 of 74F138.
  65.     see picture '2630.138' for details
  66.     (New IC is connected to power.)
  67.  
  68. 7.4    Make connections between pin 1-6 of 74F138 with relevant pins
  69.     of processor.   see picture '2630.138'
  70.  
  71. 7.5    Connect pin 15 of 74F138 with U305 pin 15 via wire.
  72.     see picture '2630.138'
  73.  
  74. *****    soldering part is done now !
  75.  
  76.  
  77. ************************* A T T E N T I O N **************************
  78. *                                                                    *
  79. *              Continue here with 8 MB reconstruction                *
  80. *                          (also for 16MB)                           *
  81. *                                                                    *
  82. **********************************************************************
  83.  
  84. 8.    Change pals U301 and U305 with delivered pals with same
  85.     print-on.               see picture '2630.pals'
  86.  
  87.  
  88. 9.    Mounting of rams '8 MB reconstruction' :
  89.  
  90.     U400 - U415        see picture '2630.rams'
  91.  
  92.     Mounting of rams '16 MB reconstruction' :
  93.  
  94.     U400 - U431
  95.  
  96. 10.    Check complete reconstruction :
  97.     Check out cold soldering points and/or short-circuits!!
  98.  
  99.  
  100. 11.    Put back A2630 into your computer.
  101.  
  102. 12.    Perform ramtest with A2630 on-board checkroutine :
  103.  
  104. 12.1    After switch-on, hold down right mousebutton immediately.
  105.     A white screen with blue text and blue gadgets will appear.
  106.  
  107.     While holding down right mousebutton press following keys :
  108.     RIGHT-AMIGA + SHIFT + M
  109.  
  110.     Monitor-program will come up.
  111.  
  112.     To test lower 8 MB-memory, type in following command :
  113.     t 200000 a00000
  114.  
  115. 12.2    Different bit-patterns are tested and reported.
  116.  
  117.     Test will be terminate by CTRL-C.
  118.     (this procedure can take some time, be patiently.
  119.     To accelerate termination, perform reset by pressing following keys:
  120.     CTRL + LEFT-AMIGA + RIGHT-AMIGA (and continue with step 12.1)
  121.  
  122.     To test upper 8 MB-memory, type in following command :
  123.     t 8200000 8a00000
  124.     (see step 12.2)
  125.  
  126. We hope you will enjoy this reconstruction and your work-out is done
  127. successful.
  128.  
  129. In case of problems and/or more detailed informations, contact:
  130.  
  131. good old GERMANY   :))
  132.  
  133. Name      : Dirk Timmermann              Name      : Thomas Riedel
  134. Town      : 27755 Delmenhorst            Town      : 28757 Bremen
  135. Street    : Jaegerstr. 138               Street    : Gerhard-Rohlfsstr.33
  136. Telephon  : (49) 4221-66199              Telephon  : (49) 421-665512
  137.  
  138.